Manuale di officina gilera fuoco. Reading : Manuale Di Officina Gilera Fuoco 2019-02-05

Manuale di officina gilera fuoco Rating: 7,1/10 979 reviews

Gilera Fuoco 500 Manuale Officina download

manuale di officina gilera fuoco

Engine - Fit the seeger ring. . Ecco finalmente una guida chiara e completa per te che ti aiuterà a preparare e migliorare lo scooter per portarlo al massimo delle potenzialità. Remove the sliding stem locking device retainers indicated in the photograph. Right wheel turning sensor Red 5B.

Next

Gilera Fuoco Manuale Officina, ferri, Milan (2019)

manuale di officina gilera fuoco

Engine Specific tooling 020262Y Crankcase splitting strip 020335Y Magnetic support for dial gauge Characteristic Standard clearance: 0. Queste istruzioni passo-passo e le immagini molto dettagliate contenute nel manuale di riparazione, ti guideranno nella manutenzione ottimale per un Gilera Fuoco 500 perfettamente efficiente. When refitting, tighten the two screws to the pre- scribed torque and use Threadlock. In order to do that, remove the connector from the other bulbs so that you can adjust one headlamp at a time. Engine - Remove the blow-by reed valve with the relevant sealing gasket. Specific tooling 020460Y Scooter diagnosis and tester Make sure that the throttle valve is supporting the stop screw.

Next

sito con manuali Gilera

manuale di officina gilera fuoco

Engine Intermediate gear - Check that the toothing is not worn. Engine - Fit the valves, the springs and the spring retaining washers. Engine - Insert the locking ring into the special tool, with the opening in the position indicated on the tool. Per maggiori informazioni sui tuoi diritti ai sensi delle Normative che regolano i Contratti dei Consumatori, ti invitiamo a consultare Conosci i Tuoi Diritti. Engine - For the flywheel side half-crankcase, special at- tention should be given to the lubrication channels for the main bearings and to the compartment and the channels for the oil pump, as well as to the duct for the by-pass located on the flywheel cover.

Next

Gilera Fuoco Manuale Officina, ferri, Milan (2019)

manuale di officina gilera fuoco

È esattamente quello utilizzato dai meccanici professionisti della Gilera. This is located before the cartridge filter and both are installed on the flywheel cover, so that the seal of the filter is subject to the pressure of the circuit. Suspensions Remove the suspension tilt locking device pipes from the headstock. Tooling Stores code Description 020360Y 52 x 55 mm adaptor 020364Y 25 mm guide 020376Y Adaptor handle 020382Y012 bush valve removing tool 020412Y 15 mm guide 020424Y Driven pulley roller casing fitting punch 020431Y Valve oil seal extractor. Le spese di spedizione internazionale vengono pagate a Pitney Bowes Inc.

Next

GILERA FUOCO 500IE MANUAL Pdf Download.

manuale di officina gilera fuoco

Insert the remote control key to be programmed in the steering lock key block. The correct fluid level for front and rear brakes. Engine Characteristic Maximum allowable run-out: 0. Maintenance Hub oil Check -Park the vehicle on its centre stand on flat ground; - Remove the oil dipstick «A», dry it with a clean cloth and put it back into its hole tightening it completely; Remove the dipstick and check that the oil level is slightly over the second notch starting from the lower end;. Re- place them in case of signs of abnormal wear. In all four-stroke engines, a loss of efficiency in oil performance and consumption should be considered normal.

Next

.:Gilera Fuoco 500 Manuale Officina in ITALIANO:.

manuale di officina gilera fuoco

Specific tooling 020376Y Adaptor handle 020375Y 28 x 30 mm adaptor 020363Y 20 mm guide Hold the crankcase in a perfectly horizontal posi- tion, heat it with a heat gun at a temperature of about 120 °C, use the specific tool to fit the bearing. Lo metto qui, poi qualcuna delle suocere si opccupoerà di sistemarlo: Se date un'occhiata al sito, ci sono migliaia di manuali da scaricare. Con questo manuale sarai in grado di poter effettuare la manutenzione ordinaria e straordinaria della moto, seguendo le istruzioni per, ad es. Chassis - Undo the two screws fixing it to the frame. Grazie a questo manuale d'officina, che ti spiega ogni singolo componente dello scooter, com'è fatto e a cosa serve, anche tu con un poco di buona volontà, potrai effettuare tutte le riparazioni da solo!!! Engine Refitting the driven pulley - Insert the new oil guards - Insert the new O-rings N. Maintenance Follow these steps to reset the service icons: 1. Suspensions With a thickness gauge, check that the air gap be- tween the screw head and the sensor is between 0.

Next

GILERA FUOCO 500 SERVICE STATION MANUAL Pdf Download.

manuale di officina gilera fuoco

Suspensions Hold the crankcase in a perfectly horizontal posi- tion, heat it with a specific heat gun at a tempera- ture of about 120 °C, use the specific tool to fit the bearing of the electric motor. Safeguarding the environment Sections marked with this symbol indicate the correct use of the vehicle to prevent dam- aging the environment. In case of anomalies, proceed as follows. Using the appropriate tool with adapter, compress the springs and insert the cotters in their seats. Suspensions Extract the electric motor bearing with the specific tool. Chassis Battery - Raise the saddle.

Next

GILERA FUOCO 500IE MANUAL Pdf Download.

manuale di officina gilera fuoco

Seat - Raise the saddle. Refit the flexible transmission control lever as shown in the figure. Characteristic Standard diameter: 22 + 0. Electrical system first key to be stored to memory: this becomes particularly important because it is the only key that enables the control unit to be wiped clean and reprogrammed for the memorisation of the service keys. This might depend on the inefficiency of the immobiliser aerial or the transponder. L'importo è soggetto a modifica fino al momento del pagamento.

Next