Where accurate measurements are required, they can only be made using calibrated, precision instruments. This manual provides general descriptions for accomplishing service and repair work with tested, efective tehniques. Screen label English For E-02, 03, 24, 28, 33 21. When replacing fasteners, always use the same type part number fastener as removed. The meaning of each symbol is also included in the table. Use engine oil unless otherwise specified.
After your payment, you will have instant access to your download! Symbol Definition Torque control required. If contact tension is not enough, rectify the contact to increase tension or replace. No special emphasis is put on replacing sealing components as we assume that these items are replaced during any repair. Troubleshooting and electrical service procedures are combined with detailed wiring diagrams for ease of use. Where usage is not obvious the tool is shown in use. Hayabusa Models Covered 1999-2000 This.
Otherwise, accurate measurements may not be obtained and personal injury may result. Lubricate themPlease note, however, that the warnings and cautions when specified. Air Cleaner Element Inspection B815H20206002 1Inspect air cleaner elementEvery 6 000 km 4 000 miles, 12 months I815H1020002-01Inspection 5 Reinstall the drain plug. If continuity is cause the inside of the tester to be burned. Brake pedal pivot and footrest pivot 3.
Major lubrication points are indicated as follows. Following them will help assure reliability. The illustrations in this manual are used to highlight the fundamental principles and procedures of basic interventions. After installing a work and if the coupler is refitted with the seal rubber circlip, always ensure that it is completely improperly positioned, it may result in poor water seated in its groove and securely fitted. Following these instructions will ensure that the motorcycle will not exceedemission standards and it will also ensure the reliability and perfomance of the motorcycle. Always use the correct special service tools or equipment specified.
Initially at 1 000 km 600 miles, 2 months and every 12 000 km 7 500 miles, 24 months thereafter! This service manual is specifically written for the do-it-yourselfer as well as the experienced mechanic. Be sure to mix it above 50% even though the atmospheric temperature does not go down to the freezing point. This manual will help you know the motorcycle better so that you can assure your customers of fast and reliableservice. Also I310G1000011-01 check for condition of the coupler lock if equipped. Connect the probe as shown to terminal contact.
Improper repair may result in injury to the mechanic and may render the motorcycle unsafe for the rider and passenger. Fuel For Other Countries Gasoline used should be graded 95 octane ResearchMethod or higher. However, it contains enough detail and basic information to make it useful to the owner who desires to perform his own basic maintenance and repair work. Footrest pivot : Apply grease. This service manual has been specially prepared so that the explanation is very simple. Never push in the probe where male terminal is supposed to fit. Always select good quality engineoil.
Also check the Never apply grease material to switch contact points to coupler for locking looseness , corrosion, dust, etc. All information, illustration and specifications contained in this manual are based on the latest product information avaiable at the time of publication approval. Apply or use brake fluid. The seal rubber may end gap larger than required to slip the possibly come off the position during disconnecting circlip over the shaft. These groups contain general information, diagnosis, testing, adjustments, removal, installation, disassembly, and assembly procedures for the systems and components. Indicates special information to make maintenance easier or instructions clearer.
. Providing that the service schedules are respected, the customers can be sure of obtaining the maximum satisfaction and best result from his car. They may not represent the actual motorcycle exactly in detail. Information on the troubleshooting, servicing specification lists, tightening torque, checking and adjusting, disassembling and assembling and servicing which cover procedures, precautions, factory specifications and allowable limits. The terminals must be clean and free cause the male terminal to bend or the female of any foreign material which could impede proper terminal to open.
This part should be understood before proceeding with troubleshooting, disassembling and servicing. The general rules are as follows. Unless specific values are given, all threaded connections should be tightened according to the required tightening torques listed on torque charts. Use fork oil L01 or equivalent fork oil. A basic knowledge of mechanics, including the proper use of tools and workshop procedures is necessary in order to carry out maintenance and repair work, satisfactorily. Otherwise, diagnosis will be wrong. The future performance and reliability of theUse distilled water only.